Products

Mask Cleaning Wipes (Non-Alcohol)
- Use mask cleaning wipes routinely for respirator maintenance
- Large 5″x8″ wipes
- Individually packaged
- Active ingredient: Benzalkonium Chloride
- For use on respirator face pieces where the manufacturer recommends using a non-alcohol cleaning wipe
- Part number: 1400-96 (100 per box), 1400-97 (30 per box)

Peel-Off Lens Covers
- Lens covers protect against paint and chemical overspray
- Full face 003-990125, Hood 003-991025, Shield 9650-25

BreatheMate® Filter Retainers
- For use with any BreatheMate® cartridge and filter respirators
- Part number: 300-1717

Respirator Storage Bag
- Storage bag is airtight to protect your respirator from shop contaminants and humidity.
- Part number: 9401-18

Low Pressure Single Airline Hose
- NIOSH approved when used with our Supplied Air Respirators
- Constructed from rugged polyvinyl chloride and reinforced with braided polyester yarn
- Hoses provide a temperature range from -20 degrees Fahrenheit to 150 degrees Fahrenheit
- Maximum Pressure: 185 PSI at 70 degrees Fahrenheit

Air Intake Extension
- Use when necessary to extend pump air intake to ensure clean air to user
- 25 feet hose section
- Extend intake up to 200 feet
- Part number: 9700-25 (1st section), 9700-30 (additional extension)

Bitrex™ Fit Test Kit
Part number: 9401-01
Includes:
- Easy to use qualitative fit test kit
- Bitrex™ produces a bitter taste for detection of leaks
- 1-Test hood
- 1-Box sensitivity solution 9401-03
- 1-Box Bitrex™ test solution 9401-04
- 1-Nebulizer for Solution Test 9401-05
- 1-Nebulizer for Sensitivity Test 9401-05

Seal Check Ampules
- Easy to use
- Isopropyl acetate, needed for qualitative fit testing
- Quantity: 10 per pack
- Part number: 1400-98

Service Kit
Kit includes:
• 1-Head strap with yoke
• 1-Exhalation valve
• 1-Cap and support
• 2-Inhalation valve and support

Pump Service Kits
- Part number: 9700-40 (1/4 and 1/3 HP oil-less pumps), 9700-49 (1/2 and 3/4 HP models 0822/1022), and 9700-50 (1/2 and 3/4 HP models 0823/1023)
Kit includes:
• 1-Intake filter
• 1-Exhaust filter
• 1-Set carbon vanes (4)

Air Exhaust Filter and Intake Filters
- Designed to keep dust and airborne particles from damaging the pump
- Replace filters every 90 – 100 running hours
- Part number: A 9700-14, B 9700-01, C 9700-02

Carbon Vanes
- Replacing the carbon vanes is crucial to maintaining proper performance and avoiding down time
- Recommend replacing vanes every 2 years
- Always replace entire set of vanes at the same time
- Part number: 9700-52 (1/2 and 3/4 HP models 0822/1022), 9700-53 (1/4 and 1/3 HP models 0522/0523), and 9700-54 (1/2 and 3/4 HP models 0823/1023)
⚠Warning: This product can expose you to chemicals including Crystaline Silica which is known to the State of California to cause cancer. For more information, visit www.P65Warnings.ca.gov.

Pure-Air 2000™ Carbon Monoxide Monitor
- Battery operated carbon monoxide monitor (AA batteries included) 2001-95
- Barbed orifice not included
- Part number: 2001-95

Pump Coupler and Plug
- 9700-10 Coupler .25″ NPT
- 9813-21 Plug, threaded .25″ NPT

Pure-Air 2000™ Replacement Filter
- Use to replace filter inside the Pure-Air 2000 filtration unit
- Part number: 2001-50